GF-0362 Ceiling Medallion

GOLD FINISHED PRODUCTS

Warranty Statement
uDecor, Inc. provides a LIMITED LIFETIME WARRANTY to the original purchaser of our Gold finished products. This LIMITED LIFETIME WARRANTY provides that the SUBSTRATE material will be free from manufacturer defects in material and workmanship under normal and expected use. This warranty does not encompass all of the products sold by uDecor, Inc. and is exclusive to our Gold finished products only. Other products may carry their own manufactures warranty. Call us at 1-877-550-0600 for details.

uDecor, Inc. provides a LIMITED 1 YEAR WARRANTY to the original purchaser on the FINISH of our Gold finished products. This LIMITED WARRANTY provides that the FINISH on the material will be free from finishing defects under normal and expected use for a period of one (1) year from the date of purchase. This warranty does not cover failure of a customer applied finishing system caused by material incompatibility nor does it cover finish failure due to customer neglect.

• Products are for decorative use only
• The Gold Finish must be protected with a clear coat. The Gold is thin and susceptible to mechanical damage if care is not taken.
• Material should be installed with non-corrosive fasteners and adhesives in accordance with the installation instructions.
• Cut edges should be covered with clear coating to prevent contamination & peeling.
• Gold products should not be installed in areas that experience ambient or surface temperatures above 140°f.
• Gold products are not recommended for exterior or wet location installation. If the material is installed in one of these areas, protective measure must be taken for reasonable product performance.
• Products should be stored flat in normal ambient temperatures at all time.

If the material proves to be defective and has been installed and existed within the bounds of the above requirements, the customer should contact uDecor, Inc. in writing or by phone within 30 days of discovering the material defect. uDecor, Inc. may require digital images, a sample of the material or a combination of material and images to be sent to uDecor, Inc. for evaluation. Upon review of materials and installation methods, uDecor, Inc. will determine if replacement, repair or refund is appropriate. uDecor, Inc. is not liable for the cost of labor, transportation, or any other expenses incurred in conjunction with the purchase, use and installation of the material.

This limited warranty does not cover damage from the result of mishandling in transportation, acts of God, customer modifications, vandalism, misuse, abuse, improper maintenance, unreasonable care, or other causes that did not arise from manufacturer defects in workmanship and/or materials. No person or entity is authorized to change, modify, or amend the terms of this limited warranty in any manner.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This warranty applies to our Gold finished products only.

TO MAKE A CLAIM

If you believe there is a defect and want to make a claim under this warranty, please notify:

uDecor, Inc.
8302 Espresso Drive, Suite 130
Bakersfield, CA 93312
1-877-550-0600
www.uDecor.com

INSTRUCTIONS-
Materials & Tools Needed
Screw Gun / Brad Gun
Adhesive / Caulking Gun
Caulking (paintable latex)
Utility Knife
Drill / Hole Saw

Painting
Many of our medallions have very intricate details and can be very difficult to finish once installed. We recommend painting your medallion before installing it. A high-quality spray paint, Latex or faux finishes work great. You can then touch up any areas that need attention after the installation is complete.

Adhesive
You can use any adhesive that is rated for use with polyurethane (check the back of the label) -- we have had great success using Red Devil Construction Adhesive, Loctite Powergrab and PL Premium Polyurethane Adhesive, all of which work well and are readily available at most home improvement stores.

Installation - No Fixture
Run a 1/4" continuous bead of adhesive around the outer edge and randomly in other areas on the back of the ceiling medallion. Press the medallion up into place using a few finish nails or screws to secure the medallion while the adhesive dries. Once the medallion is in place you can caulk any holes and around the perimeter of the medallion using a paintable caulking. Touch up the paint if needed.

Installation - With Fixture
If you are installing the medallion with a ceiling fan, chandelier or light, make sure the power is shut off at the breaker before attempting installation. Turning off the light switch WILL NOT prevent you from being shocked. If you have any doubts call an electrician.

Medallions are for decorative purposes only and cannot support the weight of a fan or light fixture. Your fixture must be supported by a support or junction box in the ceiling.

Many of our medallions come with solid centers to allow you to cut the correct size hole for your application. Take the bracket for your ceiling fan or light fixture and trace the area that you want to remove from the ceiling medallion. You will need a hole large enough for the wiring and holes for the bolts to pass through to affix your bracket to the junction box. The polyurethane material is easily cut so you can use a hole saw or a drill to punch out a hole. The hole doesn't have to be perfect since the fixture canopy will cover the hole.

Dry fit your medallion in place on the ceiling to make sure all of the wiring and fixture parts will fit as planned. Run a 1/4" continuous bead of adhesive around the outer edge and randomly in other areas on the back of the ceiling medallion. Feed through all the wiring and then press the medallion up into place, using a few finish nails or screws to secure the medallion while the adhesive dries.

Once the medallion is secure, attach your fixture bracket to the junction box. You may need longer bolts or a longer threaded tube that came with your fixture to accommodate the thickness of the medallion. Once the fixture bracket is in place, attach your ceiling fan or light fixture to the bracket and complete the wiring per your fixture's instructions. Once the wiring is complete slide the canopy into place to cover the hole of the medallion. Prior to doing the final finish work, turn on the breaker and test to make sure your fixture has been properly wired.

Now that you have your medallion and fixture installed, caulk any holes and around the perimeter of the medallion using a paintable caulking. Touch up the paint if needed.